McAfee M-1250 - Network Security Platform Uživatelská příručka

M-1250/M-1450 Sensor Product GuideRevision BMcAfee® Network Security Platform

LED Status DescriptionFan GreenAmberFan is operating.The fan has failed.Management PortSpeedGreenAmberOffThe port speed is 1000 Mbps.The port speed is

2Before you installThis chapter describes the best practices for deployment of Sensors on your network. Topics includesystem requirements, site planni

• Only trained and qualified personnel should be allowed to install, replace, or service thisequipment.• Before working on an equipment that is connec

5Verify you have received all parts.These parts are listed on the packing list and in Contents of the Sensor box.6Remove the Slide Rail Kit.7Pull out

2Before you installUnpack the Sensor14McAfee® Network Security Platform M-1250/M-1450 Sensor Product Guide

3Setting up the SensorThis chapter describes the process of setting up a Sensor to prepare it for configuration.Contents Setup overview Position

To mount the Sensor on a rack, you will attach two mounting ears to the Sensor, then mount the earsto the rack. The Sensor ears attach to either the f

Mount the Sensor by securing the ears to two posts or mounting strips in the rack. Because the earsbear the weight of the entire Sensor, be sure to fa

3Setting up the SensorPower on the Sensor18McAfee® Network Security Platform M-1250/M-1450 Sensor Product Guide

4Attaching cables to the SensorFollow the steps outlined in this chapter to connect cables to the various ports on your M-1250/M-1450 Network Security

COPYRIGHTCopyright © 2014 McAfee, Inc., 2821 Mission College Boulevard, Santa Clara, CA 95054, 1.888.847.8766, www.intelsecurity.comTRADEMARK ATTRIBUT

2Connect the other end of the Console port cable directly to a COM port of the PC or terminal serveryou will use to configure the Sensor, for example,

2Connect the other end of the cable to the network device such as a hub, switch, or a router,through which you want to respond to attacks.Cable the Ma

Default Monitoring port speed settingsMake sure that the switch/router ports connected to the Sensor monitoring ports match the Sensorconfiguration.Ta

3Connect the other end of each cable to the network devices that you want to monitor.For example, if you plan to monitor traffic between a switch and

Task1Plug a Cat 5/Cat 5e crossover cable into port 4A of the active Sensor.2Connect the other end of the cable to the port 4A of the standby Sensor.Fi

AM-1250/M-1450 Sensor specificationsThe following table lists the specifications of the M-1250/M-1450 Sensor:Sensor Specifications DescriptionDimensio

AM-1250/M-1450 Sensor specifications26McAfee® Network Security Platform M-1250/M-1450 Sensor Product Guide

BRegulatory, compliance, and safetyinformationThe Sensor meets the following standards:Sensor regulatory, safety, and complianceRegulatory: Products w

Sensor regulatory, safety, and compliance• Radiated Emissions• Conducted Emissions• EN 61000-3-2: 2000 Harmonic Current Emissions• EN 61000-3-3: 1995

IndexAabout this guide 5auxiliary port 20Cchasis 16, 17, 19conventions and icons used in this guide 5Ddocumentationaudience for this guide 5product-sp

ContentsPreface 5About this guide ... 5Audience ... 5Conventions ...

700-2395B00

Index 29Contents4McAfee® Network Security Platform M-1250/M-1450 Sensor Product Guide

PrefaceThis guide provides the information you need to configure, use, and maintain your McAfee product.Contents About this guide Find product d

Tip: Suggestions and recommendations.Important/Caution: Valuable advice to protect your computer system,software installation, network, business, or d

1Introducing Network Security SensorsThis section describes the McAfee® Network Security Sensors at a high-level and also describes theMcAfee® M-1250/

Network Access Control of hosts is regulating access to network resources based on host SystemHealth level (Standard/ DHCP NAC), identity of the user

3One RS-232C Console port, which is used to set up and configure the Sensor.4One RS-232C Auxiliary port, which may be used to dial in remotely to set